Insights

Notes from the lab bench.

Practical writing on calibration, uncertainty and test equipment, from the engineers who do the work every day. 25 articles since 2019.

4 min read

Building a calibration management programme from scratch

Growing teams often discover they have dozens of instruments and no system. A step-by-step approach to building a calibration programme that runs itself.

3 min read

Loop and temperature calibrators in oil, gas and process plants

Field calibrators are the reference for thousands of transmitters and loops. If the calibrator is wrong, every instrument it touches is wrong too.

3 min read

VNA verification vs user calibration: why you need both

You calibrate your network analyzer with a cal kit every day. So why does it still need to go to a calibration lab? The two processes answer different questions.

3 min read

How to pack and ship test equipment for calibration

Most damage to instruments happens in transit, not on the bench. A practical checklist for getting your equipment to the lab and back safely.

3 min read

Setting calibration intervals with data, not habit

Twelve months for everything is easy to administer but rarely optimal. How to use as-found history to set intervals you can defend.

3 min read

Time and frequency: GNSS-disciplined references and counter calibration

Every instrument with a clock has a frequency error. How GNSS-disciplined oscillators provide traceable frequency, and what that means for your counters and timebases.

3 min read

In-lab or on-site calibration: how to choose

On-site calibration saves downtime, but the lab offers tighter control and broader capability. A practical comparison to help you decide.

4 min read

RF power sensors and the calibration factor table

A power sensor's accuracy depends on a table of correction factors across frequency. If that table is wrong or out of date, every reading is wrong too.

4 min read

Your instrument was out of tolerance. What happens next?

An out-of-tolerance notice is not a disaster, but it does start a clock. Here is a practical approach to impact assessment that will stand up to an audit.

3 min read

Power supplies and electronic loads: what calibration covers

Bench supplies and loads are often treated as utilities rather than instruments. If they set or measure values you rely on, they need calibrating too.

4 min read

Preparing for an ISO 9001 audit: the calibration records auditors look for

Measurement equipment is one of the most common sources of audit findings. Here is what clause 7.1.5 asks for, and how to have the evidence ready.

3 min read

Clamp meters and insulation testers: a guide for electrical contractors

The two instruments every electrical contractor relies on, and the two most likely to come back from site damaged. What calibration covers and how to keep them reliable.

4 min read

Pass, fail or indeterminate? Decision rules and guard bands

When a measurement lands close to a tolerance limit, uncertainty decides the verdict. ISO/IEC 17025 now requires labs to say how they make that call.

3 min read

Signal generator calibration: level, frequency and spectral purity

A signal generator is a reference that your other measurements depend on. Here is how we verify that it produces what it says it does.

3 min read

Heat, humidity and dust: how the UAE summer affects your test equipment

Instruments are specified for a comfortable lab at 23 °C. Many of ours spend August in a vehicle on a site in Ras Al Khaimah. Here is what that does to them.

3 min read

As-found vs as-left: why you should insist on both

The as-left result tells you the instrument is good now. The as-found result tells you whether everything you measured last year was good. Only one of them is about the past.

3 min read

Spectrum analyzer calibration: beyond the frequency reference

Checking the 10 MHz reference is only the start. Amplitude accuracy, frequency response, noise floor and phase noise all determine whether your analyzer tells the truth.

3 min read

Traceability explained: the chain from the SI to your bench

Every calibration certificate claims traceability. Here is what that actually means, how the chain is built, and what breaks it.

4 min read

Oscilloscope calibration: what we actually check

Bandwidth, rise time, vertical gain, timebase and trigger. A walk through an oscilloscope calibration and why each test matters for the measurements you make.

3 min read

Keeping calibration on schedule when everything else has stopped

Movement restrictions have disrupted maintenance plans across the UAE. Here is how we are keeping instruments in calibration, and how you can avoid a backlog later in the year.

3 min read

Measurement uncertainty in plain language

Every result on a calibration certificate comes with a ± figure. What does it mean, where does it come from, and why should you care?

3 min read

How often should you calibrate a digital multimeter?

Twelve months is the default answer, but it is rarely the right one for every meter. Here is how to think about calibration intervals for the most common instrument on any bench.

3 min read

Calibration, verification and adjustment are not the same thing

Three words that are used interchangeably on purchase orders but mean very different things. Knowing the difference helps you order the right service.

4 min read

What a calibration certificate actually tells you

A certificate is more than proof that an instrument visited a lab. Here is how to read one, section by section, and what to look for before you file it away.